Instructional video— Alpha Pro Cut New Honda Smart Key on S2 Jaw
Thanks for your attention for us.
Today, we would like to show you how to cut new Honda smart key on S2 jaw by Alpha Pro
Two parts for the instructional video
Part 1: Decode and cut by original key
Part 2: Do all key lost
Let’s decode and cut by original key now
Please note that new Honda smart key can insert one side into cylinder only
We will use the Side B of S2 single-sided key jaw to cut this key.
To avoid wasting key blanks, please do calibration on S2 Jaw before decoding and cutting.
Now let’s enter into the corresponding key data.
Well, after enter the key data, we will see there are distinguish for Side A and Side B. A photo of original key will be better for reference.
Side A: Key tip towards down and deep root milling groove
Side B: Key tip towards up and shallow root milling groove
Let’s decode Side A firstly.
Click “Decode” and open ”Round” as this key is usually not worn.
Fix Side A of the original key to S2-B as shown on picture.
After fixing well, please remove the stopper and click “Decode” to start decoding.
Debris must be cleaned from jaw & decoder.
Side A decode done, please click “Switch” to Side B and click “Decode” to start decoding Side B without change any default value.
After fixing well, please remove the stopper and click “Decode” to start decoding.
Debris must be cleaned from jaw & decoder.
Well, all decoding is done, we can start to cut Side B directly.
Please click “Cut” to enter cutting page.
The default cutter is 2.0mm, please make sure to use 2.0mm cutter.
The material of this key is special, please adjust the cutting speed less than 5 to avoid damage cutter.
Fix Side B of a key blank on S2-B guided by a stopper and remember to remove stopper after fix well.
Click ”Cut” to start cutting.
Debris must be cleaned from jaw & decoder and the shield should be closed during cutting.
Side B cut done, open the shield and clean debris to get the key blank, and then fix the Side A to S2-B by stopper.
Click “Switch” to Side A and “Cut” without change any default value to start cutting.
Debris must be cleaned from jaw & decoder and the shield should be closed during cutting.
Now all cutting is done. We can verify the new key is working very well !!!
Comparison for Side A and Side B
Decode and cut is done
Next Let’s do all key lost for New Honda smart key by Alpha Pro.
The code of this cylinder is V320.
After disassemble the cylinder, please put the side where the two whole wafers can be pulled out towards you, so we can distinguish as Group A and Group B as shown on picture. Please note the cylinder cannot be opened if Group A and Group B is opposite.
After pull out the separated wafers, they are shown on picture.
Group A has 4 wafers: T5,T5,T4,T1 from A1 to A4, namely the biting number are 5543. Please note the words in blue color in the video.
Group B has 3 wafers: T1,T3,T3 from B1 to B3, namely the biting number is 133.
Then let’s input the biting numbers into the machine.
After entering into key data of 1480, click “Input” and input “5543” to Side A, then switch to Side B, click “Input”and input “133” to Side B.
Then switch to Side A and click “Cut” to enter cutting page.
The default cutter is 2.0mm, please make sure to use 2.0mm cutter.
The material of this key is special, please adjust the cutting speed less than 5 to avoid damage cutter.
Fix Side A of a key blank on S2-B guided by a stopper and remember to remove stopper after fix well.
Click “Cut” to start cutting.
Debris must be cleaned from jaw & decoder and the shield should be closed during cutting.
Cutting Side A is done, open the shield and clean debris to get the key blank, and then fix Side B to S2-B by stopper.
Click “Switch” to Side A and “Cut” without change any default value to start cutting.
Debris must be cleaned from jaw & decoder and the shield should be closed during cutting.
Now all cutting is done. You can see all wafers are in perfect position after insert the new key into the cylinder.
It verifies that the new key is working very well.
More details please kindly check the video